|
Author
|
Topic: Sorry more dumb questions.
|
Fastymz
Moderator Posts: 11429
From: Reno Nv USA MEM#1240
Registered: Apr 2001
|
posted 05-20-2003 07:32 PM
   
I need to know do all,351w have the same firing order.And do the all run the same weight balancer and flexplate-flywheel.
And do all 302-351 have the plugs numbered the same,like number is always the passenger front?Do truck motors and car motors all have all the same firing order,balancer weight,ect.
And does an 86 AOD bolt up to a 85 351w that had a C6.
Thanks for putting up with me. 
I'm really learning here,soon I might need to ask any more questions.Soon as in 10-20 years. 
------------------
SCOOP
oddly obsessed with big scoops on little Mustangs 2.26 60'S
14.9 @ 90.86MPH 65 coupe,351w,C4,Big Boss 429 hood scoop,8"3.40 TracLoc,Cragar SS,Black Suede. https://mustangsandmore.com/ubb/Fastymz.html
IP: Logged |
scottford351
Journeyman Posts: 47
From: reedsville ohio usa
Registered: May 2003
|
posted 05-20-2003 11:05 PM
all 351w use the same firing order as well as h.o. 302 unless the camshaft has been replaced with a early 302 or non h.o. All small blocks have the same cylinder order,1-4 pass. side 5-8 dr. side. As far as i know all 351w were 28"oz imbalance,the same as early 289-302s.The c6 flex plate doesnt work with a AOD because the dish where the converter bolts on is too far back, it would push the converter snout to deep into the pump. hope this helps.
IP: Logged |
Fastymz
Moderator Posts: 11429
From: Reno Nv USA MEM#1240
Registered: Apr 2001
|
posted 05-21-2003 11:25 AM
Thanks,Are there different flex plates for AOD or are they all the same.
I have an AOD flex plate put it's off a different AOD and 351w then the one's I have. ------------------
SCOOP
oddly obsessed with big scoops on little Mustangs 2.26 60'S
14.9 @ 90.86MPH 65 coupe,351w,C4,Big Boss 429 hood scoop,8"3.40 TracLoc,Cragar SS,Black Suede. https://mustangsandmore.com/ubb/Fastymz.html
IP: Logged |
scottford351
Journeyman Posts: 47
From: reedsville ohio usa
Registered: May 2003
|
posted 05-21-2003 01:44 PM
as long as it is a 28"oz it will work. the c4 flywheel with the 11 1/4 bolt pattern will also work.
IP: Logged |
Fastymz
Moderator Posts: 11429
From: Reno Nv USA MEM#1240
Registered: Apr 2001
|
posted 05-21-2003 06:34 PM
quote:
Originally posted by scottford351:
as long as it is a 28"oz it will work. the c4 flywheel with the 11 1/4 bolt pattern will also work.
How do you tell if it's a 28oz or not?
Is the 11 1/4 bolt pattern for the torque convertor or what bolt pattern does that refer to
------------------
SCOOP
oddly obsessed with big scoops on little Mustangs 2.26 60'S
14.9 @ 90.86MPH 65 coupe,351w,C4,Big Boss 429 hood scoop,8"3.40 TracLoc,Cragar SS,Black Suede. https://mustangsandmore.com/ubb/Fastymz.html
IP: Logged |
Mustangsandmore Forums
UBBFriend: Email This Page to Someone! 
