Brought to you in part by:

.


JC Whitney clearance center!
  Mustangsandmore Forums
  Ford Racing
  89 supercharged stroker rebuild woes - HELP!

Post New Topic  Post A Reply
profile | register | preferences | faq | search

next newest topic | next oldest topic
Author Topic:   89 supercharged stroker rebuild woes - HELP!
superchg89
Journeyman

Posts: 2
From: san mateo, CA , USA
Registered: Aug 2004

posted 08-19-2004 08:23 PM     Click Here to See the Profile for superchg89   Click Here to Email superchg89     Edit/Delete Message   Reply w/Quote
Brand new 342 stroker motor has new Holly systemmax 30lb injectors, trickflow twisted wedge heads, MSDBTM ignition, 6lb supercharger, PRO-M mass air, and 3 step chip (again, all brand new). My car initially started rich with rough idle, but under wide open throttle all power available. The car has less than 20 minutes running and won't start now. The cranking speed is weak but I installed a new battery. When I did a compression check, it showed only 90lbs per cylinder. I was told that gas got into the cylinders, but not much. I readjusted the valves and at this point I am uncertain whether I should pull the motor to replace the rings or if the problem is computer related. Or...? I need more info and any input is appreciated, so thanks.

IP: Logged

N266fords
Gearhead

Posts: 1652
From: Sierra Vista ,Az USA
Registered: Apr 2003

posted 08-19-2004 08:30 PM     Click Here to See the Profile for N266fords   Click Here to Email N266fords     Edit/Delete Message   Reply w/Quote
don't know if it will help but are you running a gear reduction mini starter also who checked all the tolorance where they right. after running for 20 minutes the metal expands and tolorances lessen causing more drag this and a weak starter might be your problems also whats your timing set at? it might be to advanved! these are just thought or possiblities good luck. I dont think pulling the moter is needed. have you removed the plugs and read them.
bruce

IP: Logged

steve'66
Gearhead

Posts: 9476
From: Sonoma,CA,USA
Registered: Mar 2000

posted 08-19-2004 10:18 PM     Click Here to See the Profile for steve'66   Click Here to Email steve'66     Edit/Delete Message   Reply w/Quote
See if it turns over by hand before trying to start it again. If it's locked up, I'd pull it.

SteveW

IP: Logged

Big D
Gearhead

Posts: 5461
From: WELLS, NEVADA USA
Registered: Nov 2000

posted 08-20-2004 02:35 AM     Click Here to See the Profile for Big D   Click Here to Email Big D     Edit/Delete Message   Reply w/Quote
It's turning over but won't start.. Do you have spark.. Do you have a STEEL GEAR in the distributor.. A CAST IRON GEAR will only last for minutes.. Hope this isn't the case..

------------------
Don
6T6 Fastback
331 STROKER,, WC T-5

Royal Blue Metallic w/Ghost Flames
http://mustangsandmore.50megs.com/MembersPics/BigD.html

IP: Logged

All times are ET (US)

next newest topic | next oldest topic

Administrative Options: Close Topic | Archive/Move | Delete Topic
Post New Topic  Post A Reply
Hop to:

Contact Us | Mustangsandmore Front Page

Copyright 2005, Steve LaRiviere. All Rights Reserved.


Ultimate Bulletin Board 5.47d

Amazon Honor System Click Here to Pay Learn More

[Acronyms][Calendar][Chat][Classifieds] [Members' Pics]

[ Mustangsandmore.com Bookstore] [ Smokin' Fords] [Tech Articles]