|
Author
|
Topic: shifter help
|
RONNIE
Journeyman Posts: 91
From: MD
Registered: Jan 2003
|
posted 06-04-2004 06:33 AM
   
i putting a new shifter in my mustang ii,is there any differance between the b&m pro shifter and the hurst pro ratchet.as far has installing them i don;t have much room were it hooks to the trans. thanks------------------
www.ronsmustangii.net
IP: Logged |
steve'66
Gearhead Posts: 7701
From: Sonoma,CA,USA
Registered: Mar 2000
|
posted 06-04-2004 09:58 PM
Ronnie,They are both cable operated and I doubt there is much difference in how they attach to the tranny. SteveW
IP: Logged |
John Holloway
Gearhead Posts: 744
From: Romeoville Illinois
Registered: Jul 2000
|
posted 06-04-2004 10:59 PM
Ronnie,the proshifter tells you to adjust the cable with the trans in 1st(low) gear...is that the way you did it? I just put a b&m proshifter in my mustangII.
IP: Logged |
Stang72
Gearhead Posts: 121
From: Arkel,Zuid-Holland,Holland
Registered: Jan 2003
|
posted 06-05-2004 02:11 AM
Hi, i just want to wish you a lot of luck..i just installed a B&M Hammer in my Mustang i had to hook it up to a FMX...took me 4 hours to adjust.... 
IP: Logged |
RONNIE
Journeyman Posts: 91
From: MD
Registered: Jan 2003
|
posted 06-05-2004 08:51 AM
quote:
Originally posted by John Holloway:
Ronnie,the proshifter tells you to adjust the cable with the trans in 1st(low) gear...is that the way you did it? I just put a b&m proshifter in my mustangII.
thanks for the info iam going to put it in this weekend, ronnie
------------------
www.ronsmustangii.net
IP: Logged |
RONNIE
Journeyman Posts: 91
From: MD
Registered: Jan 2003
|
posted 06-05-2004 08:53 AM
[QUOTE]Originally posted by Stang72:
Hi, i just want to wish you a lot of luck..i just installed a B&M Hammer in my Mustang i had to hook it up to a FMX...took me 4 hours to adjust.... [/QUOTEdid you install it in the console or the floor,
IP: Logged |
Stang72
Gearhead Posts: 121
From: Arkel,Zuid-Holland,Holland
Registered: Jan 2003
|
posted 06-06-2004 04:29 AM
on the floor,..my car doesn't have a console..it's kinda in the original floor position,..but had to put it 2" to the rear because that there's a support beam in the floor which was causing the selectorcable coming out of the shifter to be in such of an angle it wouldn't shift properly...good luck Ben
IP: Logged |
RONNIE
Journeyman Posts: 91
From: MD
Registered: Jan 2003
|
posted 06-06-2004 09:04 AM
THANKS FOR ALL THE INFO ON THE SHIFTER.COULD ANY OF YOU JOIN MY NEW WEB SITE IT ONLY TAKES A FEW MINUTES AND PLEASE POST AS MANY PICTURES AS YOU WANT THANKS ALOT RONNIE groups.msn.com/ronniesracingphotos
------------------
[This message has been edited by RONNIE (edited 06-06-2004).]
IP: Logged |
Mustangsandmore Forums
UBBFriend: Email This Page to Someone! 
