|
Author
|
Topic: Trick Flow Nitrous kit?
|
Dubz
Gearhead Posts: 1888
From: Manitoba Canada
Registered: Oct 2002
|
posted 05-07-2004 09:28 PM
   
i've been looking for a kit that will give me a 50 hp shot with adjustability up to a 100 shot, and found the trick flow tfx50-200 in 50 increments anyone had experience or know of anyone who has ran this kit (preferably someone who ran the carbed setup not the efi)? ------------------
1974 Gran Torino(351W/c6)
My Page
shooting for 14's this year
IP: Logged |
Fstln69
Gearhead Posts: 560
From: Westmont,il
Registered: Jan 2003
|
posted 05-08-2004 08:15 AM
I think edelbrock makes one too and there stuff WORKS!------------------
69 fairlane 351w 12.94@103mph before M&M.. after [email protected] always in search of more HP and faster ET'S Fstln69 Pics Page
IP: Logged |
Dubz
Gearhead Posts: 1888
From: Manitoba Canada
Registered: Oct 2002
|
posted 05-08-2004 02:06 PM
ohh, very nice, the performer kit comes with 50-75-100. That'll do the trickanyone have experience with this kit? [This message has been edited by Dubz (edited 05-08-2004).]
IP: Logged |
Fstln69
Gearhead Posts: 560
From: Westmont,il
Registered: Jan 2003
|
posted 05-08-2004 09:54 PM
Ok i know ill get s**** for this but my buddy used the kit 150shot on a 509 chebbie in a chassis car went 9.08 off the spray went 8.12 on it with 150 edelbrock pills! i'd say that does the trick.I have a NOS Bigshot but i think i am going to go to the 200-500 hp plate by edelbrock.Btw Billy Glidden helped design these systems
Dennis------------------
69 fairlane 351w 12.94@103mph before M&M.. after [email protected] always in search of more HP and faster ET'S
66 brandx outlaw s/s Fstln69 Pics Page [This message has been edited by Fstln69 (edited 05-08-2004).]
IP: Logged |
Dubz
Gearhead Posts: 1888
From: Manitoba Canada
Registered: Oct 2002
|
posted 05-09-2004 07:51 PM
yah, i'm not looking for anything THAT big, just a nice kick in the pants to make up for the extra weight my car carries
IP: Logged |
Dubz
Gearhead Posts: 1888
From: Manitoba Canada
Registered: Oct 2002
|
posted 05-10-2004 01:20 PM
would i ditch my 4 hole spacer, or would it work above the nitrous plate?
IP: Logged |
CometGT1974
Gearhead Posts: 412
From: Asheville, NC USA
Registered: Jan 2002
|
posted 05-10-2004 03:03 PM
It will work, i'm running a wilson 4-hole spacer over my big shot plate. Distribution seems good up to about a 250 shot, I haven't gone over that.....If it is a standard/straight 4-hole spacer you may need to taper it to get the distribution right.... In my opinion, the Nitrous Pro Flow kits are just about the best "off the shelf" nitrous kit...... [This message has been edited by CometGT1974 (edited 05-10-2004).] [This message has been edited by CometGT1974 (edited 05-10-2004).]
IP: Logged |
Dubz
Gearhead Posts: 1888
From: Manitoba Canada
Registered: Oct 2002
|
posted 05-10-2004 04:40 PM
quote:
Originally posted by CometGT1974:
It will work, i'm running a wilson 4-hole spacer over my big shot plate. Distribution seems good up to about a 250 shot, I haven't gone over that.....If it is a standard/straight 4-hole spacer you may need to taper it to get the distribution right.... In my opinion, the Nitrous Pro Flow kits are just about the best "off the shelf" nitrous kit......
well as i said i'd only be looking at up to 100hp shot, so distribution should be fine then. What's the nitrous pro flow kit you mentioned? and what may be differences between nitrous companys, better solenoids, just the name? would there be much or any difference for a 100 max shot?
IP: Logged |
Mustangsandmore Forums
