Brought to you in part by:

.


JC Whitney clearance center!
  Mustangsandmore Forums
  Ford Racing
  9" Question

Post New Topic  Post A Reply
profile | register | preferences | faq | search

next newest topic | next oldest topic
Author Topic:   9" Question
RickBook
Gearhead

Posts: 140
From: Houston, TX
Registered: Apr 2002

posted 03-13-2003 02:49 PM     Click Here to See the Profile for RickBook     Edit/Delete Message   Reply w/Quote
I'm refurbing the 9" going into my Maverick. I know diddely about 9" Ford Rears (only that they're hell stout).

I came across a fitting on the top of the axle housing. I assume it is a vent?

What is to vent to? There are two outlets, one steel and one rubber hose.

My Q: What am i supposed to do with this? Get a breather for it and go? Other?

Thanks,

Rick
p.s. Can one attach an image from the C:/Drive to a post?

[This message has been edited by RickBook (edited 03-13-2003).]

IP: Logged

Tea'sGrabber
Gearhead

Posts: 276
From: Seattle, Wash.
Registered: Feb 2003

posted 03-13-2003 02:56 PM     Click Here to See the Profile for Tea'sGrabber   Click Here to Email Tea'sGrabber     Edit/Delete Message   Reply w/Quote
There should be a rubber line just above the housing in your car. It attaches to it.

------------------
Todd 71 Mav Grabber All orig 306 cu.in. Cast Iron heads. Carillo Rods.Best et. 10.71 @ 124 thru the mufflers.

IP: Logged

RickBook
Gearhead

Posts: 140
From: Houston, TX
Registered: Apr 2002

posted 03-13-2003 03:11 PM     Click Here to See the Profile for RickBook     Edit/Delete Message   Reply w/Quote
This is '70 Maverick that's been off the street for sometime. If the 'rubber line' WAS there, it isn't anymore.

What would the line have run to?

[This message has been edited by RickBook (edited 03-13-2003).]

IP: Logged

Tea'sGrabber
Gearhead

Posts: 276
From: Seattle, Wash.
Registered: Feb 2003

posted 03-13-2003 03:33 PM     Click Here to See the Profile for Tea'sGrabber   Click Here to Email Tea'sGrabber     Edit/Delete Message   Reply w/Quote
I'll have to look @ mine when I get home

------------------
Todd 71 Mav Grabber All orig 306 cu.in. Cast Iron heads. Carillo Rods.Best et. 10.71 @ 124 thru the mufflers.

[This message has been edited by Tea'sGrabber (edited 03-13-2003).]

IP: Logged

SteveLaRiviere
Administrator

Posts: 43152
From: Saco, Maine
Registered: May 99

posted 03-13-2003 03:37 PM     Click Here to See the Profile for SteveLaRiviere   Click Here to Email SteveLaRiviere     Edit/Delete Message   Reply w/Quote
There are two lines hanging down. One of course is the rubber line to the rear brake lines, the other is the axle vent tube. It runs from a fitting on the axle tube on the driver's side to a fitting in the frame/subframe.

------------------
'70 Mustang Mach 1 - '72 Mustang Sprint - '94 F-150

Please remember our sponsors,
Mustangs Plus, NPD, Osborn Reproductions, MyFordPerformance.com, and FordRamAir.com

IP: Logged

All times are ET (US)

next newest topic | next oldest topic

Administrative Options: Close Topic | Archive/Move | Delete Topic
Post New Topic  Post A Reply
Hop to:

Contact Us | Mustangsandmore Front Page

Copyright 2005, Steve LaRiviere. All Rights Reserved.


Ultimate Bulletin Board 5.47d

Amazon Honor System Click Here to Pay Learn More

[Acronyms][Calendar][Chat][Classifieds] [Members' Pics]

[ Mustangsandmore.com Bookstore] [ Smokin' Fords] [Tech Articles]