|
Author
|
Topic: new dyno figures
|
two89w
Gearhead Posts: 144
From: sydney australia
Registered: Sep 2002
|
posted 10-23-2002 09:38 AM
   
235kw or 315rwhp at 6000rpm,450nm or 331foot pounds
IP: Logged |
rockafellz
Gearhead Posts: 914
From: San Lorenzo, CA, USA
Registered: Aug 2001
|
posted 10-23-2002 10:15 AM
 Pretty impressive!! What were you running again?Erik ------------------
1966 Ford Mustang 2+2
Mine - Restomod in Progress 1966 Ford Mustang Coupe
Dad's - Original Unrestored
IP: Logged |
two89w
Gearhead Posts: 144
From: sydney australia
Registered: Sep 2002
|
posted 10-23-2002 05:37 PM
10.1comp,347,comp cams 294s,windsor snr's,quad webers,
IP: Logged |
Skeeter
Journeyman Posts: 95
From: California
Registered: Dec 2001
|
posted 10-23-2002 05:41 PM
quote:
Originally posted by two89w:
10.1comp,347,comp cams 294s,windsor snr's,quad webers,
How are those webbers working out for you? I have 48IDA"s that i might put on my 418w. They are just a big pain in the @#$ to tune.
J.
IP: Logged |
two89w
Gearhead Posts: 144
From: sydney australia
Registered: Sep 2002
|
posted 10-23-2002 05:51 PM
they still have a stumble at 3000rpm and it needs 48mm's but they are ok besides that
IP: Logged |
Skeeter
Journeyman Posts: 95
From: California
Registered: Dec 2001
|
posted 10-23-2002 05:52 PM
quote:
Originally posted by two89w:
they still have a stumble at 3000rpm and it needs 48mm's but they are ok besides that
what car is the 347 in. How about gears and tranny?
thanks,
J.
IP: Logged |
two89w
Gearhead Posts: 144
From: sydney australia
Registered: Sep 2002
|
posted 10-23-2002 05:55 PM
68 mustang coupe,4.1 diff,tremec 3550
IP: Logged |
V8 Thumper
Gearhead Posts: 2991
From: Orange, Ca. United States of America
Registered: Dec 2001
|
posted 10-23-2002 06:09 PM
 Are you still running the Webbers, or ???
IP: Logged |
Skeeter
Journeyman Posts: 95
From: California
Registered: Dec 2001
|
posted 10-23-2002 06:57 PM
V8 thumper? are you asking me? If so, I dont have the motor together yet. I will get it going with a single four and I might put the webbers on later. Not sure yet.J.
IP: Logged |
two89w
Gearhead Posts: 144
From: sydney australia
Registered: Sep 2002
|
posted 10-24-2002 03:13 AM
any takers for a rough flywheel hp figure?
IP: Logged |
V8 Thumper
Gearhead Posts: 2991
From: Orange, Ca. United States of America
Registered: Dec 2001
|
posted 10-24-2002 10:03 AM
355-360
IP: Logged |
rockafellz
Gearhead Posts: 914
From: San Lorenzo, CA, USA
Registered: Aug 2001
|
posted 10-24-2002 10:08 AM
~350FWHPQuad webers, tremec and 4.11:1 rear? You guys don't mess around there!! Erik ------------------
1966 Ford Mustang 2+2
Mine - Restomod in Progress 1966 Ford Mustang Coupe
Dad's - Original Unrestored
IP: Logged |
two89w
Gearhead Posts: 144
From: sydney australia
Registered: Sep 2002
|
posted 10-24-2002 04:34 PM
didnt have the money for fuel injection  ,and the competition with in the club is fierce
IP: Logged |
Mustangsandmore Forums
UBBFriend: Email This Page to Someone! 
