|
Author
|
Topic: left over parts
|
bfxcomet
Gearhead Posts: 671
From: Port Alberni, B.C. , Canada
Registered: Mar 2001
|
posted 02-05-2005 08:50 PM
   
Cleaning out the shop.
66 390 and C6
289 block and 3 or 4 sets of heads
73 t-bird hub caps
65 comet hub caps
69 fairlane hub caps
3 -60's power steering pumps
68/69 fairlane drivers door window regulator
65 comet parts and trim
64 fairlane 500 horn ring
67 or 68 falcon disc brakes with spindles
mustangII front end
F-250 4X4 hub caps
79 F-250 hub caps
9in rearend from a 76 grand marque
64 Marauder dash insert
Roger------------------
65 comet project
84 T-bird 289/C4 13.74/99mph street/strip
www.avdra.bc.ca
Made in CANADA built for speed
#1145
IP: Logged |
bfxcomet
Gearhead Posts: 671
From: Port Alberni, B.C. , Canada
Registered: Mar 2001
|
posted 02-07-2005 10:01 PM
Add to the list,
55 ford tail lights
56 ford tail lights
pics available for all items.
Roger------------------
65 comet project
84 T-bird 289/C4 13.74/99mph street/strip
www.avdra.bc.ca
Made in CANADA built for speed
#1145
IP: Logged |
trashline
Gearhead Posts: 1217
From: Levittown, Pa
Registered: Dec 2003
|
posted 02-07-2005 11:24 PM
have any 65/66 v8 manual steering parts?I need both inner and outer tie rods and the center drag link. i also need an idler/pitman arm ------------------
1966 coupe
200ci, 3.03 3 speed
holley weber two barrel, msd 6a, blaster 2 coil, Duraspark I, 2 inch exhaust to a super turbo, stock rear (3.20),ram air(homemade)
white w/ black interior, soon be painted (i hope) with the R model apron 1968 Ford Fairlane 289 auto rotting away 1979 f150 300 six with a three on the tree
IP: Logged |
bfxcomet
Gearhead Posts: 671
From: Port Alberni, B.C. , Canada
Registered: Mar 2001
|
posted 02-08-2005 01:27 AM
No I don't have any spare manual steering parts left.
Roger------------------
65 comet project
84 T-bird 289/C4 13.74/99mph street/strip
www.avdra.bc.ca
Made in CANADA built for speed
#1145
IP: Logged |
Hukdunfonix
Journeyman Posts: 20
From: San Diego, Ca. USA!
Registered: Dec 2004
|
posted 02-09-2005 12:06 AM
will those breaks work on a 68 mustang coupe? and is it hte full assembly?
IP: Logged |
Dubz
Gearhead Posts: 1640
From: Manitoba Canada
Registered: Oct 2002
|
posted 02-09-2005 12:45 AM
what year and castings would the heads be? Any of them have work done?
Would be nice to get a good set from someone inside canada so i don't have to deal with border stuff.
IP: Logged |
bfxcomet
Gearhead Posts: 671
From: Port Alberni, B.C. , Canada
Registered: Mar 2001
|
posted 02-09-2005 09:51 AM
The disc brake set-up is spindles, calipers and rotors. I don't know about interchanging on to a mustang. They would fit I'm sure but unsure about if geometry will be right.
I have a few sets of heads; I'll get some casting # and let you know.
Roger------------------
65 comet project
84 T-bird 289/C4 13.74/99mph street/strip
www.avdra.bc.ca
Made in CANADA built for speed
#1145
IP: Logged |
bfxcomet
Gearhead Posts: 671
From: Port Alberni, B.C. , Canada
Registered: Mar 2001
|
posted 02-09-2005 10:53 PM
I have 3 sets of C6-AE and 1 set of D8-OEAB. 1 set of the C6-AE heads has had work done to them. Apparently they where on a motor that ran for a few hours before bearing failure. I could send you pics if you want.
Roger------------------
65 comet project
84 T-bird 289/C4 13.74/99mph street/strip
www.avdra.bc.ca
Made in CANADA built for speed
#1145
IP: Logged |
Dubz
Gearhead Posts: 1640
From: Manitoba Canada
Registered: Oct 2002
|
posted 02-10-2005 03:02 AM
hrmm, i know they'd have smaller combustion chamgbers than the heads i have which would be nice for compression, but i think they also have smaller valves than my currents, plus i forgot about needing to make the bolt holes bigger so they will work on my 351. Sorry but i don't think it's what i'm looking for, sorry for the inconvenience.
IP: Logged |
Mustangsandmore Forums
UBBFriend: Email This Page to Someone! 
