|
Author
|
Topic: how to, on replacing a door skin
|
trashline
Gearhead Posts: 1217
From: Levittown, Pa
Registered: Dec 2003
|
posted 02-10-2004 04:21 PM
   
how do you replace a door skin? from how to take it off to how to put it back on every tool il need and so on. i know youll need a crimping tool anything else? thanks------------------
1966 mustang coupe
200ci 3 speed tranny
msd 6a ignition, blaster 2 coil, 2 inch exhaust to a glass pac, stock rear, single out header, cold air intake (homemade).
white w/ black interior
IP: Logged |
65darkhorse
Gearhead Posts: 894
From: Northern NJ
Registered: Aug 2002
|
posted 02-10-2004 05:58 PM
here's a how-to on a '72 ~ but it should give you some idea:http://www.desertmustangs.com/1972coupe/Door_skin_repair/72-Door-skin.htm ------------------
'65 GT 302 5 spd
"Trust your instinct to the end, though you can render no reason." R.W. Emerson
Entia non sunt multiplicanda praeter necessitatem
my stang!
IP: Logged |
trashline
Gearhead Posts: 1217
From: Levittown, Pa
Registered: Dec 2003
|
posted 02-11-2004 06:51 PM
so do you think it would be the same way for a 66? then i have to paint it and what not to so.------------------
1966 mustang coupe
200ci 3 speed tranny
msd 6a ignition, blaster 2 coil, 2 inch exhaust to a glass pac, stock rear, single out header, cold air intake (homemade).
white w/ black interior
IP: Logged |
SteveLaRiviere
Administrator Posts: 42139
From: Saco, Maine
Registered: May 99
|
posted 02-11-2004 06:58 PM
Yes, it would be the same process. ------------------
'70 Mustang Mach 1 351C 4V/FMX/3.25 Open
'70 Mustang Convertible 250 I6/3 speed/2.79 Open
'72 Mustang Sprint Hardtop 351C 4V/FMX/4.30 Trac Loc
'94 F-150 XL 5.8L/E4OD/3.55 Limited Slip
IP: Logged |
trashline
Gearhead Posts: 1217
From: Levittown, Pa
Registered: Dec 2003
|
posted 02-11-2004 07:02 PM
ok cool thanks steve ------------------
1966 mustang coupe
200ci 3 speed tranny
msd 6a ignition, blaster 2 coil, 2 inch exhaust to a glass pac, stock rear, single out header, cold air intake (homemade).
white w/ black interior
IP: Logged |
68 S-code GT
Gearhead Posts: 2194
From: Sayreville, NJ, US
Registered: Mar 2000
|
posted 02-13-2004 12:15 PM
That?s a pretty good site with some good shots but they don?t have any of the guy folding over the lips. Eastwood has some tools for this! I?ve been wanting to do this myself but I keep talking myself out of it. 
IP: Logged |
trashline
Gearhead Posts: 1217
From: Levittown, Pa
Registered: Dec 2003
|
posted 02-13-2004 12:42 PM
yea it sounds pretty tough for me (being twenty) but im will to try anything. ------------------
1966 mustang coupe
200ci 3 speed tranny
msd 6a ignition, blaster 2 coil, 2 inch exhaust to a glass pac, stock rear, single out header, cold air intake (homemade).
white w/ black interior
IP: Logged |
Mustangsandmore Forums
UBBFriend: Email This Page to Someone! 
