|
Author
|
Topic: Hey... four speed guys
|
V8 Thumper
Gearhead Posts: 3529
From: Orange, Ca. United States of America
Registered: Dec 2001
|
posted 01-10-2002 08:31 AM
   
On a 289 w/ 10 1/2" clutch and stocker z-bar linkage, what luck have you guys had with different discs/plates? I was intending to run the 'King Cobra' from FMS, seems it's not applicable to early flywheels (damn). It's going to be a street/strip car so Pep Boys remans won't cut it  [This message has been edited by V8 Thumper (edited 01-10-2002).]
IP: Logged |
7DMACH1
Gearhead Posts: 1517
From: PHILA. PA.
Registered: Feb 2001
|
posted 01-10-2002 08:32 AM
Center Force. ------------------
RAY . FLY THE FLAG, SHOW THE WORLD WE ARE PROUD AMERICANS!70 MACH 1 351C NOW 408 STROKER 4SPD.
86 MERCURY CAPRI 5.0 RUNS 12.86 @107 1.65 60 ft.
2001 LINCOLN LS V8 1997 MUSTANG
SHOW THE WORLD, LIGHT A CANDLE.
http://www.geocities.com/slariviere/7DMach1.html
IP: Logged |
steve'66
Gearhead Posts: 6602
From: Sonoma,CA,USA
Registered: Mar 2000
|
posted 01-10-2002 10:16 AM
We had great results with the 10" Centerforce dual friction clutch. It will out perform the 10 1/2" King Cobra. SteveW
IP: Logged |
MrWesson22
Gearhead Posts: 1209
From: Dacula, GA
Registered: Sep 2000
|
posted 01-10-2002 01:51 PM
Chalk up another vote for Centerforce. I love my dual friction!
------------------
Neal
Member #723
[email protected] AIM: MrWesson22 69 Gulfstream Aqua Grande
351C/Toploader 4sp
IP: Logged |
Dr. Who
Gearhead Posts: 164
From: Redwood City, Ca.
Registered: Sep 2001
|
posted 01-10-2002 02:16 PM
I vote Centerforce as well!------------------
Moe! Larry! Cheese! Curly Howard
IP: Logged |
Ryan Wilke
Gearhead Posts: 1539
From: Stanton, Michigan 49707
Registered: Oct 2000
|
posted 01-10-2002 04:57 PM
V8Thmpr:
I don't recall the part numbers used in my 306"/4-spd/Z-bar/9"slicks pkg; but I've had excellent service from McLeod (1st pick) and Hayes (2nd pick) stuff over the years....and yeah, I've read a bunch of good reports in the past year or two on Centerforce stuff, but never used any yet.Ryan
IP: Logged |
steve'66
Gearhead Posts: 6602
From: Sonoma,CA,USA
Registered: Mar 2000
|
posted 01-10-2002 05:19 PM
In fact, e-mail me if you want a used 10" centerforce dual friction pressure plate cheap. The disc is worn, but the pressure plate (cover) is good to go again.  SteveW
IP: Logged |
richard bohm
Gearhead Posts: 373
From: tucson,az-luray,va
Registered: May 2001
|
posted 01-10-2002 09:41 PM
i have to go with the crowd on this, centerforce. when my 66 goes together that is what i will use. the mcleod and hays are good also.
IP: Logged |
Mustangsandmore Forums
UBBFriend: Email This Page to Someone! 
