Brought to you in part by:

.

Tools and Supplies at Eastwood

  Mustangsandmore Forums
  '64 1/2 to '73 -- The Classic Mustang
  Dyno Tomorrow......

Post New Topic  Post A Reply
profile | register | preferences | faq | search

UBBFriend: Email This Page to Someone! next newest topic | next oldest topic
Author Topic:   Dyno Tomorrow......
65_289
Gearhead

Posts: 510
From:
Registered: Jul 2001

posted 08-13-2001 07:41 PM     Click Here to See the Profile for 65_289   Click Here to Email 65_289     Edit/Delete Message   Reply w/Quote
Gonna dyno the pony tomorrow. It doesn't seem to be running as hard as I think it can, so I am not expecting too much. Will post the results whe I get 'em!!!!!!

------------------
1965 Coupe, Tremec 3550, Steeda Tri-Ax, Cable Clutch conversion, 3.25 gears, Ford XB3 longblock, x303 heads, B-Cam, 9:1 comp., Ford Racing high-torque starter, Pertronix Ignitor & Flamethrower coil, Accel 8.8mm wires, 600 cfm Edelbrock carb, Edelbrock RPM intake, K&N air, Holley electric fuel pump & AFPR, dual 2-chamber Flowmasters, KYB shocks, 5-leaf springs, Chrome Export Brace, Griffen Radiator, Comp. Eng. subs.

IP: Logged

H8CHEVY
Gearhead

Posts: 239
From: Southern Cali
Registered: Jun 2000

posted 08-13-2001 07:46 PM     Click Here to See the Profile for H8CHEVY   Click Here to Email H8CHEVY     Edit/Delete Message   Reply w/Quote
sweet! how much is it costing you??? good luck!

IP: Logged

SteveLaRiviere
Administrator

Posts: 24286
From: Saco, Maine Toys: '70 Mustang Mach 1 - '72 Mustang Sprint - '94 F-150
Registered: May 99

posted 08-13-2001 07:50 PM     Click Here to See the Profile for SteveLaRiviere   Click Here to Email SteveLaRiviere     Edit/Delete Message   Reply w/Quote
Cool! Good luck.

------------------
'70 Mustang Mach 1 M code 351C 4V/FMX/3.25 open
'72 Mustang Sprint Coupe 351C 4V/FMX/4.30 Trac Lok
'94 F-150 XL 5.8L/E4OD/3.55 Limited Slip
'97 Probe GTS 2.5L DOHC
Ford. The closer you look, the better WE look!

IP: Logged

JAAZZY
Gearhead

Posts: 723
From: Bay Area, CA
Registered: Apr 2001

posted 08-13-2001 08:34 PM     Click Here to See the Profile for JAAZZY     Edit/Delete Message   Reply w/Quote
I'm not sure how much he's paying but the consensus around here seems to be about $75 for a baseline run. It's more if you want to tune and do mutliple runs. I think at that point it becomes an hourly charge.

IP: Logged

65_289
Gearhead

Posts: 510
From:
Registered: Jul 2001

posted 08-14-2001 01:51 AM     Click Here to See the Profile for 65_289   Click Here to Email 65_289     Edit/Delete Message   Reply w/Quote
It's like $40 for 1, $74 for 3, or $100/hour, I think.

------------------
1965 Coupe, Tremec 3550, Steeda Tri-Ax, Cable Clutch conversion, 3.25 gears, Ford XB3 longblock, x303 heads, B-Cam, 9:1 comp., Ford Racing high-torque starter, Pertronix Ignitor & Flamethrower coil, Accel 8.8mm wires, 600 cfm Edelbrock carb, Edelbrock RPM intake, K&N air, Holley electric fuel pump & AFPR, dual 2-chamber Flowmasters, KYB shocks, 5-leaf springs, Chrome Export Brace, Griffen Radiator, Comp. Eng. subs.

IP: Logged

All times are ET (US)

next newest topic | next oldest topic

Administrative Options: Close Topic | Archive/Move | Delete Topic
Post New Topic  Post A Reply
Hop to:

Contact Us | Mustangsandmore Front Page

Copyright 2002, Steve LaRiviere


Ultimate Bulletin Board 5.47d

Amazon Honor System Click Here to Pay Learn More

[Where are the M&M Members From?]

[Build a free Mustangsandmore.ws Home Page!]

[About M&M][Acronym Guide][Calendar of Events][Chat Room][Classified Ads] [Links]

[Members' Photos] [M&M Mug Shots] [Technical Articles][Ford Parts Number Deciphering

[ Mustangsandmore.com Bookstore] [Advertise on Mustangsandmore.com] [Mustangsandmore.com T-Shirts]